Three Zone Tube Furnace is a safe hydrogen tube furnace. The processing tube is made of high-quality Ni-based superalloy which never cracks and is broken at flowing Hydrogen gas. Two hydrogen detectors are included which will shut down the Hydrogen gas generator and gas inlet valve immediately once detecting hydrogen gas leaking. The Hydrogen Gas tube furnace is designed for processing material under hydrogen gas up to 1200°C safely. The precision temperature controller is 30 segment programmable.
Pledge: genuine guarantee,speed refund,gift insurance,seven days no reason to return
HTTF-1200-III-H2 Three Zone Tube Furnace is a safe hydrogen tube furnace. The processing tube is made of high-quality Ni-based superalloy which never cracks and is broken at flowing Hydrogen gas. Two hydrogen detectors are included which will shut down the Hydrogen gas generator and gas inlet valve immediately once detecting hydrogen gas leaking. The Hydrogen Gas tube furnace is designed for processing material under hydrogen gas up to 1200°C safely. The precision temperature controller is 30 segment programmable.
Gas Furnace Structure | Double layer steel casing with air cooling to keep furnace surface temperature lower than 80°C High purity fibrous alumina insulation for Max. energy saving Hydrogen detector and solenoid valve are included for safe operation 4 alumina tube blocks (alumina coated on the surface) are included, to be put inside of the tube before operating the equipment in order to avoid heat radiation |
Power | 11 KW Max. (50A breaker required) |
Voltage | AC 208-240 Single Phase, 50/60 Hz |
Working Temperature | Furnace continuous temperature: 1400°C (Alumina tube must be used under this temperature) Tube Max. working temperature: 1250°C (< 0.5 hours, superalloy tube can't be used over this temperature) Tube continuous temperature: 1200°C (Quartz liner inside of the superalloy tube can't be used over this temperature) |
Max. Heating Rate | ≦10°C/min (≦ 5°C/min is recommended) |
Processing Tube | Material: Nickel-based super-alloy seamless tube ( Cr20NI25Al15） Tube Size: OD 80mm x ID 72mm x Length 1200mm Temperature ≦ 1250°C, the tube can withstand pressure ≦ 0.1 Mpa Temperature ≦ 1200°C, the tube can withstand pressure ≦ 0.3 Mpa Temperature ≦ 1100°C, the tube can withstand pressure ≦ 1 Mpa Temperature ≦ 1000°C, the tube can withstand pressure ≦ 1.5 Mpa Temperature ≦ 900°C, the tube can withstand pressure ≦ 3 Mpa Temperature ≦ 800°C, the tube can withstand pressure ≦ 5 Mpa |
Heating Zone length | Three-zone total length: 600mm Zone 1: 180mm, Zone 2: 180mm, Zone 3: 180mm Constant temperature zone: 260mm ± 3°C (set the same temperature for all 3 zones) |
Temperature controller | PID automatic control with 30 segments programmable Automatic over-temperature and thermal broken protection RS485 Communications Port Advanced Temperature Control (Optional) MTS02-Y Temperature control software kit (for YD518P series controllers) + 15" laptop package is available at the options bar. You may upgrade the controller to the Eurotherm 3004 with +/- 0.1 accuracy, which is compatible with LabVIEW. This package includes a Eurotherm 3004 programmer, and a communication cable (RS485 - USB). |
Flanges and Gas Inlet | A set of SS304 flanges are included, KF-25 gas outlet port Vacuum level: 10-2 torr using a mechanical pump, 10-5 torr using a molecular pump (pump is not included) Max withstand pressure for the standard flange included is 0.3 Mpa. Customization (up to 5 Mpa) is available at an extra cost |
Hydrogen Detector System | Two Gas Detector is Integrated into the system. One is installed on the furnace to monitor potential gas leakage. The other one is portable which can be used to check other ports Working Temperature Range: -20ºC to +60ºC Detectable range: 1 - 1000 ppm Two-level Alarm Point: First level alarm point: once it reaches 50 ppm, the alarm is trigged Second level alarm point: once it reaches 100 ppm, it will shut off the inlet valve to the H2 automatically |
Gas-outlet Flow-meter | One 1000 ml/min floating meter is installed on the gas-outlet end for adjusting gas flow rate 1/4" Dia stainless steel tube is installed for burning hydrogen gas during gas flowing One long lighter is included in the standard package for igniting hydrogen gas manually One 6" long neck flexes safe lighter is included for lighting hydrogen gas |
Heating Element | Fe-Cr-Al Alloy doped by Mo |
PC Connection | RS485 port is installed in front of the panel for PC connection. PC control module and software are included for computerized temperature control The new version of PC module is now compatible with Lab View 05/08/2014 |
Dimension | 1750mm L x 700mm W x 750 mm H |
Net Weight | 110 Kg |
Warranty | One year limited warranty for electrical and mechanical parts |
Warning | Tube furnaces with alumina tubes are designed for use under vacuum and low pressure < 0.12 atm (absolute pressure) The flow rate for gases should be limited to < 200 SCCM for reducing thermal shocks to the tube Attention: A two-stage pressure regulator must be installed on gas cylinder to limit the pressure to below 3 PSI for safe operation. Vacuum limit definition for all quartz tube furnaces: up to 1000° |
HTTF-1200-III-H2 Three Zone Tube Furnace is a safe hydrogen tube furnace. The processing tube is made of high-quality Ni-based superalloy which never cracks and is broken at flowing Hydrogen gas. Two hydrogen detectors are included which will shut down the Hydrogen gas generator and gas inlet valve immediately once detecting hydrogen gas leaking. The Hydrogen Gas tube furnace is designed for processing material under hydrogen gas up to 1200°C safely. The precision temperature controller is 30 segment programmable.
Gas Furnace Structure | Double layer steel casing with air cooling to keep furnace surface temperature lower than 80°C High purity fibrous alumina insulation for Max. energy saving Hydrogen detector and solenoid valve are included for safe operation 4 alumina tube blocks (alumina coated on the surface) are included, to be put inside of the tube before operating the equipment in order to avoid heat radiation |
Power | 11 KW Max. (50A breaker required) |
Voltage | AC 208-240 Single Phase, 50/60 Hz |
Working Temperature | Furnace continuous temperature: 1400°C (Alumina tube must be used under this temperature) Tube Max. working temperature: 1250°C (< 0.5 hours, superalloy tube can't be used over this temperature) Tube continuous temperature: 1200°C (Quartz liner inside of the superalloy tube can't be used over this temperature) |
Max. Heating Rate | ≦10°C/min (≦ 5°C/min is recommended) |
Processing Tube | Material: Nickel-based super-alloy seamless tube ( Cr20NI25Al15） Tube Size: OD 80mm x ID 72mm x Length 1200mm Temperature ≦ 1250°C, the tube can withstand pressure ≦ 0.1 Mpa Temperature ≦ 1200°C, the tube can withstand pressure ≦ 0.3 Mpa Temperature ≦ 1100°C, the tube can withstand pressure ≦ 1 Mpa Temperature ≦ 1000°C, the tube can withstand pressure ≦ 1.5 Mpa Temperature ≦ 900°C, the tube can withstand pressure ≦ 3 Mpa Temperature ≦ 800°C, the tube can withstand pressure ≦ 5 Mpa |
Heating Zone length | Three-zone total length: 600mm Zone 1: 180mm, Zone 2: 180mm, Zone 3: 180mm Constant temperature zone: 260mm ± 3°C (set the same temperature for all 3 zones) |
Temperature controller | PID automatic control with 30 segments programmable Automatic over-temperature and thermal broken protection RS485 Communications Port Advanced Temperature Control (Optional) MTS02-Y Temperature control software kit (for YD518P series controllers) + 15" laptop package is available at the options bar. You may upgrade the controller to the Eurotherm 3004 with +/- 0.1 accuracy, which is compatible with LabVIEW. This package includes a Eurotherm 3004 programmer, and a communication cable (RS485 - USB). |
Flanges and Gas Inlet | A set of SS304 flanges are included, KF-25 gas outlet port Vacuum level: 10-2 torr using a mechanical pump, 10-5 torr using a molecular pump (pump is not included) Max withstand pressure for the standard flange included is 0.3 Mpa. Customization (up to 5 Mpa) is available at an extra cost |
Hydrogen Detector System | Two Gas Detector is Integrated into the system. One is installed on the furnace to monitor potential gas leakage. The other one is portable which can be used to check other ports Working Temperature Range: -20ºC to +60ºC Detectable range: 1 - 1000 ppm Two-level Alarm Point: First level alarm point: once it reaches 50 ppm, the alarm is trigged Second level alarm point: once it reaches 100 ppm, it will shut off the inlet valve to the H2 automatically |
Gas-outlet Flow-meter | One 1000 ml/min floating meter is installed on the gas-outlet end for adjusting gas flow rate 1/4" Dia stainless steel tube is installed for burning hydrogen gas during gas flowing One long lighter is included in the standard package for igniting hydrogen gas manually One 6" long neck flexes safe lighter is included for lighting hydrogen gas |
Heating Element | Fe-Cr-Al Alloy doped by Mo |
PC Connection | RS485 port is installed in front of the panel for PC connection. PC control module and software are included for computerized temperature control The new version of PC module is now compatible with Lab View 05/08/2014 |
Dimension | 1750mm L x 700mm W x 750 mm H |
Net Weight | 110 Kg |
Warranty | One year limited warranty for electrical and mechanical parts |
Warning | Tube furnaces with alumina tubes are designed for use under vacuum and low pressure < 0.12 atm (absolute pressure) The flow rate for gases should be limited to < 200 SCCM for reducing thermal shocks to the tube Attention: A two-stage pressure regulator must be installed on gas cylinder to limit the pressure to below 3 PSI for safe operation. Vacuum limit definition for all quartz tube furnaces: up to 1000° |
